|
转载自:www.1000bbs.com 千家网整理日期: 2005-09-11
1...第一份 nitsuko tx-2464(nec ak 2464)
nitsuko tx-series system programming
1.system programming procedure
1.1 description
tx-824/1232/2464 system user can change the system data flexibly. tx-824/1232/2464
system is available only from the display telephone that is connected to phisical port
no.1.
1.2 system initialzation
1. power supplytch is off condition.
2. when entering programming mode st first time, thetch-1 on the nx7e-408m-a1 or
nx7e-24cpu-a1 unit should be set at the left side for int. power supplytch is on.
(the system datas are initialized.)
int 1
run
rst 2
3. after you changed system data, you must set thetch-1 knob to right side for int to
protect your system data.
int 1
run
rst 2
note：if you exited programming mode that did not set the right position attch-1, the
display is indicated as follows：
c h e c k s w s e t t i n g
－－c
you should be operated as follows：
（1）press #. （return to the programming mode）
（2）check thetch-1 position. （set the right side for int）
（3）press hold key. （exit from programming mode）
1.3 system reset
tch-2 (rst/run) is used to system reset. in case that the position is set to rst side,
then the system shall be reset (stored data to be remained) at once.
1.4 to connect the single line telephone
tx-824/1232/2464 system can be connected the single line telephone (slts) without
changing the hardware but can not judge the instrument type only connect the slt. when
you connect the slt first time, you must operate as follows for system to be understood.
－method 1：off-hook and hang up. (once)
－method 2：on the program #13-e, assign "1 ? connected".
in the each cases, when slt is disconnected, you have to assign the "0 ? not connected" in
program #13-e.
1.5 enter the system data setting operation
1. (on-hook condition) press opac key.
2. dial #, *, #, * and password (8 digits)
3. press hold key.
password can be set depend on the system data (initial：8111111). password\'s digits are
optional from 1 to 8 digits, and dial from 0 to 9.
when you forgot password, you dial bypasscode (10 digits) which are indicated on each
dials. you can enter the system data set up mode.
1.6 key institution
0-9：to use item number, extension number, trunk number and the other number.
*：go to next.
#：exit from current program number.
opac：to use dial data so on clear.
2. feature programming
2.1 the general rules of programming
1. dial program number （1-99）
2. dial *
3. dial assigning objective.
4. dial *
5. dial option numbers.
6. dial *
7. repeat steps 5-6 if more than one option.
8. dial *
2.2 example of programming
program #01 each line assignment 1 (method)
dial
display
meaning
1
programming 01
programming no. 1
*
line assignment1 01-00
4
line assignment1 01-04
line no. 4
*
line assignment1 01-04-10100
3
line assignment1 01-04-10003
type of line (3: behind pbx
1
line assignment1 01-04-10031
dial mode (1: dtmf)
4
line assignment1 01-04-00314
queuing group (4: group 4)
1
line assignment1 01-04-03141
pbx night mode (1: enable)
0
line assignment1 01-04-31410
polarity reserve detection (0:
disable)
*
line assignment1 01-05-10100
ready for line no. 5
#
programming 00
terminate this item
2.3 end (at item number input condition)
press "hold" key.
note：dial # to exit from current program number before pressing hold key.
when protecttch on the nx&e-408m-a1 or nx7e-24cpu-a1 unit is set to initial side
or error data are programmed, you can not get out from data set up mode.
3. commands description
3.1 program 1
this program assigns a line type (co/pbx), a dial mode (pulse/dtmf), a queue group, a
pbx night mode and a polarity reverse detection (only 1232/2464 system) to each outside
line.
【display indication】
line assignment1
01-ln-abcde
【input data】
ln. line number (01-syatem max)
a：line type
0: no connection 1: co line 2: not used 3: pbx line
b：dial mode
0: dp (pulse dial) 1: dtmf
c：queuing group
0: not assigned 1-6: group 1- group 6
d：pbx night mode
0: disable 1: enable
e：polarity reserve detect (only tx-1232/2464)
0: disable 1: enable
※ when the line is unused, the line must be assigned "no connection" in line type.
【initial】
abcde：11100 (all)
3.2 program 2
this program assigns co/pbx lines to line groups for outgoing/incoming use. only
consecutive lines can be grouped (e.g. 3,4,5). lines in one group can overlap with lines in
another.
【display indication】
line groups
02-gp-st-ed
【input data】
gp.： line group number (01-30)
st.： lowest numbered line in group (01-system max)
ed.： highest numbered line in group (01-system max)
【initial】
(group 1)： st: 01 ed: 08 (other)： st: 00 ed: 00
3.3 program 3
this program assigns a disa line, a disa access mode, a common use line and a non-
restricted line to an outside line.
【display indication】
line assignment2
03-ln-abcde
【input data】
ln.： line number (01-system max)
a：direct inward system access (disa) line
0: disable 1: enable
b：disa line access
0: not access 1: day mode 2: night mode 3: day and night mode
c：common use line assignment
0: can not use as a common line 1: can not as a common line
d：non-restricted lines
0: restriction 1: non-restriction
e：not used. (this item has to be programmed as "0")
【initial】
abcde：00000 (all)
3.4 program 4
this program assigns the function for each extension.
【display indication】
stn assignment1
04-st-abcde
【input data】
st.：extension number (10-system max)
a：executive override
0: not allowed 1: allowed with tone 2: allowed without tone
b：co off-hook signalling
0: disable 1: enable
c：intercom off-hook signalling
0: none 1: when dial 2: when busy
d：intercom signal call
0: disable 1: enable
e：headset
0: disable 1: enable
【initial】
abcde：00000 (all)
notes：when extension is assigned the signal call mode in program #04-d after system
has been assigned the voice call mode in program #19-b, this extension
are signal call mode, but the other extensions are kept the voice call mode.
when extension is assigned the voice call mode in program #04-d after system
has been assigned the signal call mode in program #19-b, all extensions
are signal call mode regardless of program #04-d.
3.5 program 5
this program assigns a extension port to an unsupervised conference circuit. in the tx-824,
1232, 2464system, the unsupervised conference circuits are numbered 01-04. an extension
port assigned as an unsupervised conference port must not be terminated with a phone. in
other wards, each unsupervised conference circuits must be assigned from unused
extension ports.
【display indication】
unsup.conf.port
05 xx－st
【input data】
xx.：port no. (01-04) (can not input dial)
st.： extension port support unsupervised conference
00: not assigned 10-system max: (extension number)
※ up to 4 ports can be set in a system.
【initial】
(xx = 01-04) st：00
3.6 program 6
this program selects the line groups each extension can use for outgoing calls. up to two
outgoing line groups can be assigned to an exetension.
【display indication】
outgoing co acc.
06-st-g1-g2
【input data】
st.：extension number (10-system max.)
g1：outgoing line group 1
00: not assigned to any group 01-30: (line group number)
g2：outgoing line group 2
00: not assigned to any group 01-30: (line group number)
※ g1 and g2 shall be defined under program 01.
【initial】
g1：01 g2：00 (all)
3.7 program 7
this program selects the line groups each extension can use for incoming calls and the
audible assignments (day and / or night mode ringing) for the extensions. up to two
incoming line groups can be assigned to an exetension.
【display indication】
inc.line acc/aud
07-st-x-gpd
【input data】
st.：extension number (10-system max.)
x.： no. (1-2) (can not input dial)
gp.：incoming line group 1
00: not assigned to any group 01-30: (line group number)
d.：incoming ring type
0: no ringing 1: day ring 2: night ring 3: day and night ring
※gp shall be defined under program 02.
【initial】
(x=1)：gp: 01 d=3[no.10] d=0[no.11-no. max]
(x=2)：gp: 00 d=0
3.8 program 8
this program assigns the function for each extension.
【display indication】
stn assignment2
08-st-abcde
【input data】
st.：extension number (10-system max.)
a：instrument type
0: kts 1: disa 2: slt(dp) 3: slt(dtmf)
b：slt dial plan set
0: dial plan 1 1: dial plan 2
c：internal page zone
0: not include 1-4：page zone 1-4
d：tenant group
0: not include 1-4: tenant group 1-4
e：park hold group
0: not include 1-4: park hold group 1-4
※ when extension port has been assigned as disa in program #08-a, this port can\'t use.
【initial】
abcde：01100 (all)
notes：on the program #05 and #08-a, same extension ports (unused one) can be
assigned for both programs simultaneously. however, each port shall function
only for one task on first-in-first-out basis.
3.9 program 9
this program assigns "executive / secretary" pairs for the executive call forward feature.
up to eight such pairs can be formed. up to all eight executive extensions can be paired with
the same secretary extension, if desired.
【display indication】
exec.call fwd
09-x-ms-sc
【input data】
x ：call forwarding pair no. (1-8) (can not input dial)
ms：manager extension number (10-system max) (00: none)
sc：secretary extension number (10-system max) (00: none)
※：a maximum of 8 pairs can be programmed.
【initial】
(x=1-8) ms: 00 sc: 00
3.10 program 10
this program assigns "executive / secretary" partnerships for dual handsfree hotline. up to
four such partnerships can be assigned.
【display indication】
dual hf hotline
10-sc-m1-m2
【input data】
sc：secretary\'s extension number (10-system max) (00: none)
m1：manager_1\'s extension number (10-system max) (00: none)
m2：manager_2\'s extension number (10-system max) (00: none)
※ a maximum of 4 conbinations can be programmed.
【initial】
sc：00 m1：00 m2：00
3.11 program 11
this program assigns extensions to hunting groups for the group hunt transfer features.
up to five hunting groups can be formed, numbered 0 to 4, with a maximum of sixteen
exetensions per group.
【display indication】
hunt groups
11-n xx-st
【input data】
n：hunting group number (0-4)
xx：extension no. in pilot group (01-16) (can not input dial)
st：extension number (10-system max) (00: none)
※ a maximum of 16 extensions can be set in 1 hunting group.
【initial】
(n=0-4) (xx=01-16) st: 00
3.12 program 12
this program selects the extensions to receive the chime tones from a doorphone box. up to
ten extensions can receive the chimes from both boxes.
【display indication】
door chime box
12-n xx-std
【input data】
n：doorphone number (1-2)
xx：received extension no. (01-10) (can not input dial)
st：received extension number (10-system max) (00: none)
d：incoming ring type
0: no ringing 1: day ring 2: night ring 3: day and night ring
※ a maximum of 10 extensions can be programmed for each doorphone.
【initial】
(n=1-2) (xx=01-10) st：00 d：0
3.13 program 13
this program assigns the function for each extension.
【display indication】
stn assignment3
13-st-abcde
【input data】
st：extension number (10-system max)
a：key touch tone
0: provided 1: not provided
b：do not disturb
0: not provided 1: incoming tone disable provided 2: dnd provided
3: dnd and incoming tone disable provided
c：alarm audible
0: off 1: on
d：voice announce device port
0: disable 1: enable
e：terminal connection (for slt)
0: not connected 1: connected
【initial】
abcde：00001 (all)
3.14 program 14
this program assigns an extension number to a telephone port.
【display indication】
(start condition)
flex. sta. #ing
14-00
【input data】
※ enter the digit setting mode
1. press "*" key.
?
【display indication】
(digit setting mode)
flex. sta. #ing
14-00 －002
【input data】
※ digit set operation
1. dial "00" and "2" or "3". (2 ro 3 digits mode select)
2. press "*" key. (return to the start condition)
?
【display indication】
(2 digits mode)
flex. sta. #ing
14-st －ss
【input data】
st：extension number (10-system max)
ss：10-79 (2 digits mode) ss: 00 (not assigned)
?
【display indication】
(3 digits mode)
flex. sta. #ing
14-st －sss
【input data】
st：extension number (10-system max)
sss：100-799 (3 digits mode) sss: 000 (not assigned)
【initial】
digit：002 ss=st
notes：originally assigned extension numbers in 3 digits mode are 110 to 173. if the
customer wants other extension number within a specific range, extension
numbers must be changed by this program.
3.15 program 15
this program selects the functions for system base.
【display indication】
sys assignment1
15 -abcde
【input data】
a：lamp shift mode
0: disable 1: enable
b：night transfer
0: all tenant 1: each tenant
c：automatic line access
0: disable 1: press spk key and queuing group no. 2: (on-hook condition) dial 0
3: 1+2
d：exclusive hold
0: disable 1: enable
e：single step access
0: disable 1: enable
【initial】
abcde：00201
3.16 program 16
this program selects the functions for system base.
【display indication】
sys assignment2
16 -abcde
【input data】
a：ringing line off-hook access
0: disable 1: all call at incoming gp1 and ringing call at incoming gp2
2: ringing call at incoming gp1 and gp2.
b：recall line off-hook access
0: disable 1: enable
c：co line access for slt
0: seize the co line for outgoing call
1: seize the co line for outgoing call and held line pickup
d：add-on conference setup mode
0: increase one by one 1: increase 5 parties at once
e：multi-line conference
0: disable 1: enable
【initial】
abcde：21000
3.17 program 17
this program selects the functions for system base.
【display indication】
sys assignment3
17 -abcde
【input data】
a：dial pulse sender speed
0: 10 pps 1: 20 pps
b：make/break ratio
0: 33% 1: 39%
c：dtmf minimum pause time
0: high-speed (80 ms on - 80 ms off) 1: mid-speed (100 ms on - 100 ms off)
2: low-speed (150 ms on - 150 ms off)
d：storage quantity of abbreviated dial (only tx-1232/2464)
0: 100 1: 200
e：existence of attendant for disa
0: no ringing 1: day ring 2: night ring 3: day and night ring
【initial】
abcde：00001
2...有没有其它品牌的呀要是都综合起来就好了
3...有啊！要什么？请说，只要我有。
上面部分还未完，因为每贴只给 16k 空间，只能分开帖。
4...什么叫其他品牌都综合起来？
5...3.18 program 18
this program selects the functions for system base.
【display indication】
sys assignment4
18 -abcde
【input data】
a：three minute warning tone
0: disable 1: enable
b：repeat dial pattern
0: none 1: 30 seconds call, 3 minute wait 2: 30 seconds call, 1 minute wait
3: 30 seconds call, 30 seconds wait 4: 15 seconds call, 15 seconds wait
c：abbreviated dialing restration
0: not restricted 1: restricted
d：handset receiver volume
0: reset after conversation 1: keep this volume
e：time indication
0: 12h mode 1: 24h mode
【initial】
abcde：01000
3.19 program 19
this program selects the functions for system base.
【display indication】
sys assignment5
19 -abcde
【input data】
a：all call to external zone
0: disable 1: speaker 1 2: speaker 2 3: speaker 1 and 2
b：intercom call type
0: voice call 1: signal call
c：microphone on/off (initial condition)
0: on 1: off
d：room monitor
0: disable 1: enable
e：not used (this item has to be programmed as "0")
【initial】
abcde：10000
3.20 program 20
this program selects the functions for system base.
【display indication】
sys assignment6
20 -abcde
【input data】
a：door chime tone duration
0: 2 times 1: 30 seconds
b：paging splash tone
0: disable 1: enable
c：door alert tone
0: disable 1: enable
d：automatic line access code for slt
0: off-hook and dial 0 1: off-hook and dial 9
e：existence of doorphone box
0: doorphone 1, 2 both not 1: doorphone 1 set, 2 not
2: doorphone 1 not, 2 set 3: doorphone 1, 2 both set
【initial】
abcde：01010
3.21 program 21
this program sets the timer for exclusive hold recall. the timer can be set in 10 second
intervals, up to 2550 seconds.
【display indication】
exc.hold timers
21-n -ttt
【input data】
n：1: recall start time 2: recall signal duration time
ttt：time 000: not assigned 001-255: 10-2550 seconds
【initial】
(n=1)：ttt: 003 (n=2)：ttt: 003
3.22 program 22
this program sets two timers for the system hold feature：
1. the recall timer selects the interval of time a call stays on system hold before it recalls
(re-rings) the extension that placed it on hold. this timer can be set for 10 second intervals,
up to 2550 seconds.
2. the dutation timer determines how long the system hold recall signal lasts. the timer
can be set for a maximum of 255 seconds.
【display indication】
sys. hold timers
2-n -ttt
【input data】
n：1: recall timer 2: duration timer
ttt：time 000: not assigned 001-255: 10-2550 seconds (n=1) 1-255 seconds (n=2)
【initial】
(n=1)：ttt: 006 (n=2)：ttt=005
3.23 program 23
this program determines how long an unannounced transfer rings the receiving extension
before recalling the transferring extension. the timer can be set for multiples of 10 seconds,
up to 2550 seconds.
【display indication】
unann. xfer
timer
23 -ttt
【input data】
ttt：recall time 000-255: 0-2550 seconds
【initial】
ttt：006
3.24 program 24
this program determines how long an announced transfer stays on system hold before
recalling the transferring extension. the timer can be set in 10 second intervals, up to 2550
seconds.
【display indication】
ann\'d xfer timer
24 -ttt
【input data】
ttt：recall time 000: 1-hold transfer disabled 001-255: 10-2550 seconds
【initial】
ttt：000
3.25 program 25
this program enables or disables the call duration timer feature. if enable, the call
duration timer can be programmed to start from 1 to 255 seconds after a line is accessed.
【display indication】
call dur. start
25 -ttt
【input data】
ttt：start time 000: not indicated 001-180: 1-180 seconds
【initial】
ttt：015
3.26 program 26
this program sets the duration of the open loop flash used for the flash feature. one
duration is available for co lines and another for pbx lines. a flash duration can range
from 30 to 7500 ms (30 ms intervals).
【display indication】
flash timer
26-n -ttt
【input data】
n：line type 1: co line 2: pbx line
ttt：flash time 000: not assigned 001-250：30-7500 ms (30 ms step)
【initial】
(n=1)：ttt: 025 (n=2)：ttt: 003
3.27 program 27
this program sets two smdr timers：
1. call duration timer selects the minimum number of seconds (00-60) a call must last in
order for it to be recorded on the smdr printout.
2. call start timer selects the number of seconds (00-60) which pass before smdr starts
timing a call.
【display indication】
smdr timers
27 xx -tt
【input data】
xx：01: minimum call duration timer 02: inter-digit timer (01 and 02 can\'t input dial)
tt：time 00: not assigned 01-60: 1-60 seconds
【initial】
(xx=01)：tt: 00 (xx=02)：tt: 10
3.28 program 28
this program determines how long an extension rings before transferring a call to other
extension (ring transfer when unanswered). the timer can be set for 1 to 255 seconds.
【display indication】
delay ring timer
28 -ttt
【input data】
ttt：time 000: time out disabled 001-255: 1-255 seconds
【initial】
ttt：015
3.29 program 29
this program determines attendant revert timer. a call left on system hold longer than a
this programmed period of time, re-rings the attendant telephone (station #10 or operator
station of each tenant).
【display indication】
att. revert timer
29 -ttt
【input data】
ttt：attendant revert timer assignment
000: time out disabled 001-255: 1-255 seconds
【initial】
ttt：000
3.30 program 30
this program assigns timer for voice message features.
on the disa condition, when voice message is sent：
1. voice message transmission port is not answer automatically after ringing.
2. voice message transmission port is not on-hook after answering automatically.
this setting time passed, dial tone heard. (wait a dtmf dial condition)
【display indication】
ann. timers
30-n -ttt
【input data】
n：1: automatic answering timer 2: dt (dial tone) sent timer
ttt：attendant revent timer
000: time out disabled (use tx-824) 000: time out at once (use tx-1232/2464)
001-255: 1-255 seconds
【initial】
(n=1)：ttt: 030 (n=2)：ttt: 030
3.31 program 31
this program assigns timer of line-to-line conversation cut off.
1. on the line-to-line operation, when user forgot operation of the path connection (dial
"#"),
; as the result of silence.
2. on the line-to-line operation, when conversation finished and on-hook that the user does
not dial "#, #", line-to-line condition continued.
(1st and 2nd line keys lamp lighting red condition.)
on the (1) and (2) condition, when setting time passed, both of 1st and 2nd lines will be cut
off automatically.
【display indication】
ln. to ln. timers
31-n -ttt
【input data】
n：1: path connection waiting timer 2: warning tone timer for conversation cut off
ttt：time 000: time out disabled
001-255: 1-255 seconds (n=1) 1-255 minutes (n=2)
【initial】
(n=1)：ttt: 030 (n=2)：ttt: 030
3.32 program 32
this program determines release time of dtmf receiver.
【display indication】
pb rec. rel. timer
32 -ttt
【input data】
ttt：time 000: time out disabled 001-255: 1-255 seconds
【initial】
ttt：010
3.33 program 33
this program determines interval time between automatic cut off and seizing line on the last
number redial and repeat dial.
【display indication】
line drop timer
33 -ttt
【input data】
ttt：time 000: not time out 001-010: 1-10 seconds
【initial】
ttt：003
3.34 program 34
this program set repeat time for the automatic repeat dial.
【display indication】
rep. dial. times
34 -ttt
【input data】
ttt：repeat dial times 001-255: 1-255 times
【initial】
ttt：010
3.35 program 35
this program assigns a class of service (cos) level (0-5) to each extension.
【display indication】
class of service
30-st -abc
【input data】
st：extension number (10-system max)
a：class od service (day) 0-5：class a-f
b：class od service (night) 0-5：class a-f
c：class od service (dial block) 0-5：class a-f
【initial】
abc：005 (all)
3.36 program 36
this program selects up to 12 permitted codes, numbered 01-12. a permitted code can
contain up to the first 8 digits of the desired telephone number.
【display indication】
permitted codes
36-nn
permitted codes
dddddddd
【input data】
nn：permitted code number (01-12)
dddddddd：permitted code assignment (from 1 to 8 digits se allowed)
※ when data clear, press opac key.
【initial】
(nn=01-12) dddddddd: no setting
3.37 program 37
this program enables or disables the permitted code digit limit feature. if enabled, the
maximum number of digits per permitted code call can range from 1 to 30.
【display indication】
code digit limit
37 -dd
【input data】
dd：digit 00: no restrict 01-30: 1 digit-30 digits
※ a maximum of 30 digits can be programmed.
【initial】
dd：00
3.38 program 38
this program selects up to four different pbx access codes, numbered 1-4. a pbx access
code can be one or two digits long.
【display indication】
pbx access codes
38-n -dd
【input data】
n：pbx access code number (1-4)
dd：pbx access code (from 1 to 2 digits set allowed)
※ when data clear, press opac key.
※ amaximum of 4 types can be programmed.
【initial】
(n=1-4) dd：no setting
3.39 program 39
this program selects up to four common unrestricted codes, numbered 1-4. a common
unrestricted code can be up to four digits long.
【display indication】
comm. unrestrict
39-n -dddd
【input data】
n：common unrestricted code number 1-4: number 1-4
dddd：common unrestricted code (from 1 to 4 digits set allowed)
※ when data clear, press opac key.
※ amaximum of 4 types can be programmed.
【initial】
(n=1-4) dddd：no setting
3.40 program 40
this program selects up to 4 restricted codes for class b, numbered 1-4. a restricted code
can be up to four digits long.
【display indication】
restr. codes b
40-n -dddd
【input data】
n：restrict code number (1-4)
dddd：restrict code (from 1 to 4 digits set allowed)
※ when data clear, press opac key.
※ amaximum of 4 types can be programmed.
【initial】
(n=1-4) dddd：no setting
3.41 program 41
this program selects up to 8 restricted codes for class c and d, numbered 1-8. a
restricted code can be up to two digits long.
【display indication】
restr. codes d2
41-n -dd
【input data】
n：restrict code number (1-8)
dd：restrict code (from 1 to 2 digits set allowed)
※ when data clear, press opac key.
※ amaximum of 8 types can be programmed.
【initial】
(n=1-8) dd：no setting
3.42 program 42
this program creates walking class of service security codes. up to 10 security codes can
be created. the security codes are identified by the numbers 0-9, and each code is four digits
long.
【display indication】
unrest. sec.
codes
42-n -dddd
【input data】
n：security code number (0-9)
dddd：security code (from 1 to 4 digits set allowed)
※ when data clear, press opac key.
※ amaximum of 10 types can be programmed.
【initial】
(n=0-9) dddd：no setting
3.43 program 43
this program assigns restriction class (a to f) to each walking cos security code.
【display indication】
unrestr. class
43-n -d
【input data】
n：number (0-9)
d：restriction class 0-5: class a-f
※ "n" is corresponded security code in the program 42.
※ class shall be defined under program 35.
【initial】
(n=0-9) d：0
3.44 program 44
this program selects normally open or normally closed contacts for each alarm input.
【display indication】
alarm sensor
44-n -a-b
【input data】
n：alarm number (1-2)
a：alarm installed or not installed 0: not installed 1: installed
b：alarm trigger condition
(1) when internal power is used
0: normally contacts 2: normally open
(2) when external power is used
0: normally open 2: normally contacts
【initial】
(n=1-2) a: 0 b: 0
3.45 program 45
this program enables or disables the intercom link increase feature.
【display indication】
icm link incr.
45 -dd
【input data】
dd：end of the used line number
00: not assignment 01-system max minus 1：end of the used line number
※ when this system programming finished, this system is reset.
【initial】
dd：00
3.46 program 46
this program creates disa security codes. up to eight security codes can be created. the
security codes are identified by the numbers 1-8, and each code is four digits long.
【display indication】
disa sec. codes
46-n -dddd
【input data】
d：security code number (1-8)
dddd：security code (from 1 to 4 digits set allowed)
※ when data clear, press opac key.
【initial】
(n=1-8) dddd：no setting
3.47 program 47
this program assigns an extension number (10-system max) to a disa security code for
smdr.
【display indication】
disa sec. code st
47-n -st
【input data】
n：security code number (1-8)
st：extension number (10-system max)
※ number correspond to program 46.
【initial】
(n=1-8) st：10
3.48 program 48
this program assigns a cos level (a-f) to a disa security code.
【display indication】
disa cos
48-n -d
【input data】
n：security code number (1-8)
d：restriction class 0-5: class a-f
※ number correspond to program 46.
※ class shall be defined under program 35.
【initial】
(n=1-8) d: 0
6...3.49 program 49
this program assigns background music and / or alarm signals to an external page zone.
※ the order of priority：bgm < co line incoming tone < paging < alarm 2 < alarm 1
【display indication】
ext. zone
bgm/alm
49-n -abc
【input data】
n：external speaker number (1-2)
a：bgm 0: not send 1: send
b：alarm 1 0: not send 1: send
c：alarm 2 0: not send 1: send
【initial】
(n=1-2) a：0 b：0 c：0
3.50 program 50
this program assigns incoming co audible to an external page zone.
【display indication】
ext. zone ln/aud
50-n -gpd
【input data】
n：external speaker number (1-2)
gp：line group 00: not ring 01-30: group 01- group 30
d：incoming ring mode
0: no ringing 1: day ring 2: night ring 3: day and night ring
【initial】
(n=1-2) gp：00 d：0
3.51 program 51
this program assigns an attendant extension for disa.
【display indication】
a. a. divert sta.
51 -st
【input data】
st：extension number (10-system max)
【initial】
st：10
3.52 program 52
this program assigns features for tenant group.
【display indication】
tenant option
52-n -d
【input data】
n：feature number (1-5)
1: intercom call 2: internal paging call 3: common abbreviated dial
4: transfer to attendant 5: dss led indication (only tx-1232/2464)
d：featyre access
(n=1-2)：0: allowed 1: restrict
(n=3)：0: common used 1: assigning abbreviated dial
(n=4)：0: system 1: each tenant group
(n=5)：0: indicating all extensions in system
1: indicating extensions in the tenant group to which the dss belongs
【initial】
(n=1-5) d：0
3.53 program 53
this program assigns partition to used abbreviated dial each tenant.
【display indication】
(abbreviated dial：100)
tenant abbr. dial
53-nn-st-ed
【input data】
nn：tenant group[ number (01-04)
st：start abbreviated dial number (00-99)
ed：end abbreviated dial number (00-99)
【display indication】
(abbreviated dial：200)
tenant abbr. dial
53-nn
tenant abbr. dial
53-sta-end
【input data】
(abbreviated dial：200 = tx-1232/2464)
nn：tenant group[ number (01-04)
sta：start abbreviated dial number (000-199)
ed：end abbreviated dial number (000-199)
※ on the tx-1232/2464, when program 17-d is re-writed the data, this program is reset.
【initial】
(nn=01-04) st: 00 ed: 99 sta: 000 end: 199
3.54 program 54
this program assigns attendant extension for each tenant group.
【display indication】
tenant att. assig
54 xx-st
【input data】
xx：tenant group no. (01-04) (can not input dial)
st：each tenant group attendant 00: not assigned 10-system max: (extension number)
【initial】
(xx=01-04) st: 00
3.55 program 55
this program assigns line keys used as park hold keys for each park hold group.
【display indication】
park hd ln. assig
55-nn-st-ed
【input data】
nn：park hold group number (01-04)
st：start line key no. 00: not assigned 01-12: line key 01-12
ed：end line key no. 00: not assigned 01-12: line key 01-12
【initial】
(nn=01-04) st: 00 ed: 00
3.56 program 56
this program selects a mode of option relay.
【display indication】
relay assign
56-n -d
【input data】
n：relay number (1-2)
d：control type
0: not assigned 1: doorphone 1 2: doorphone 2 3: external m.o.h 4: bgm
【initial】
(n=1-2) d: 0
3.57 program 57
this program selects smdr option features.
【display indication】
smdr
assignment1
57 -abcde
【input data】
a：dial digits option (printout condition)
(tx-824)：0: everytime 1: more than 8 digits
(tx-1232/2464)：0: disable 1: enable
b：outgoing/incoming transfer 0: printout 1: not printout
c：no answer 0: printout 1: not printout
d：kts account code
0: input enabled 1: input forced before dial 2: input disabled
e：incoming call
0: printout everytime 1: printout when account code input
【initial】
abcde：01000
3.58 program 58
this program selects smdr option features.
【display indication】
smdr
assignment2
58 -abcde
【input data】
a：barred outgoing 0: printout 1: not printout
b：slt account code 0: input enabled 1: input disabled
c：dialed number 0: printout 1: not printout
d：not used (this item has to be programmed as "0")
e：not used (this item has to be programmed as "0")
【initial】
abcde：11100
3.59 program 59
this program assigns dial digits which is printout on smdr. this program only available
for tx-1232/2464 system, and program 57-a must enabled.
【display indication】
smdr print digit
59 -dd
【input data】
dd：dial digits 01-24: 1-24 digits
【initial】
dd：08
3.60 program 60
this program assigns polarity reserve detect time. this program can use only
tx-1232/2464 system.
【display indication】
ln. reverse timer
60 -ttt
【input data】
ttt：polarity reserve detect time 001-255：100 ms - 25.5 seconds
【initial】
ttt：008
3.61 program 62
this program assigns port which connect to the dss console. and assigns the extension
which pairs with dss console. this program can use only tx-1232/2464. each dss
console must be connected to the last port of each unit.
【display indication】
dss console port
62-n -po-st
【input data】
n：dss console no. (1-2) (can not input dial)
po：dss console port no. (17,25,33,41,49,57,65,73)
st：pair extension no. (10-system max )
【initial】
(n=1-2) po: no setting st: no setting
3.62 program 63
this program assigns data for dss console features. this program can use only
tx-1232/2464 system.
【display indication】
dss assignment1
63 -abcde
【input data】
a：automatic hold of line 0: disable 1: enable
b：dnd override 0: disable 1: enable
c：not used (this item has to be programmed as "0")
d：not used (this item has to be programmed as "0")
e：not used (this item has to be programmed as "0")
【initial】
abcde：00000
3.63 program 64
this program assigns the maximum time of personal message that each extension user can
record.
【display indication】
sys assignment7
64 -abcde
【input data】
a：maximum time of personal message 0: 4 sec. 1: 8 sec. 2: 12 sec. 3: 16 sec.
b：not used (this item has to be programmed as "0")
c：not used (this item has to be programmed as "0")
d：not used (this item has to be programmed as "0")
e：not used (this item has to be programmed as "0")
【initial】
abcde：30000
3.64 program 65
this program used for unattendant message feature.
－ item-1 in this program assigns duration time from system detects the incoming call to
system automatically answers and sends a waiting message to outside caller.
－ item-2 in this program assigns duration time from system automatically answer to system
sends cut-off message.
【display indication】
incoming timers
65-n -ttt
【input data】
n：1: automatic answer time 2: cut off time
ttt：time 000: disable 001-255: 1-255 sec.
【initial】
(n=1)：ttt: 000 (n=2)：ttt: 000
3.65 program 66
this program assigns each timer for disa.
－ item-1 in this program assigns duration time from system detects the incoming call to
system answers automatically. system can provides ring-back tone to the outside caller
by
this duration time.
－ item-2 in this program assigns waiting time for each operation. when this time has
passed,
this call will automatically be transferred to attendant extension which is assigned in
program . #51
－ item-3 in this program assigns calling time at extension by extension access feature.
when this time has passed, this call will automatically be transferred to attendant
extension which is assigned in program #51.
【display indication】
disa timers
66-n -ttt
【input data】
n：1: automatic answer time ttt：000: answer at once 001-255: 1-255 sec.
n：2: dial waiting time ttt：001-255: 1-255 sec.
n：3:extension calling time ttt：001-255: 1-255 sec.
【initial】
(n=1)：ttt: 000 (n=2)：ttt: 010 (n=3)：ttt: 030
3.66 program 90
this program enables the error check feature.
【display indication】
error
e0
【input data】
no error indication
【display indication】
error
e
?(dial "*")
error
90 xx
【input data】
error indication
xx：error of system data number.
3.67 program 91
this program enables the abbreviated dial clear, message clear and function key
initialization.
【display indication】
f-key initialize
91 *
【input data】
individually clear
3.68 program 92
this program assigns restriction class (a to f) to each walking cos security code.
【display indication】
sys. prg. password
92
sys. prg. password
dddddddd
【input data】
dddddddd：input password (from 1 to 8 digits set allowed)
【initial】
dddddddd：81111111
3.69 program 93
this program indicates sub-cpu version for each unit. (vau unit number is no.09)
【display indication】
sub cpu version
93-nn -dd
【input data】
nn：unit number (01-03): (tx-824) (01-09): (tx-1232/2464)
dd：version number (01-15) (vau) (can not input dial)
3.70 program 99
this program erases data in system buffer memory. all data entered while programming the
system is stored in buffer memory untill the programming mode is exited. the program
buffer cancelation feature erases all the data in the buffer and restores the previous values.
【display indication】
buffer cancel
99 c
【input data】
end of the system data setting (do not overwrite system data)
4. list of dial number plan
4.1 dial number plan (kts) on the on-hook condition
dial operation
features
program
0
seize the idle co line
15
*
key touch tone set/reset
13
#
background music set/reset
19
4.2 dial number plan (kts) on the off-hook condition
dial operation
features
program
extension number
call pickup to intercom call, intercom hold, hold
transfer
and disa call (specific extension).
※ extension number = 10-79 or 100-799
—
80-87
meet-me answer
—
88
meet-me answer (same paging group)
08
9
call pickup to doorphone call.
—
* + extension number + *
mw reset (specify extension)
※ extension number = 10-79 or 100-799
—
* + 0 + *
mw reset (all setting extension)
—
* # + personal code + *
dial block set
personal code = 4 digits (0000-9999)
35
* # + personal code + #
dial block reset
personal code = 4 digits (0000-9999)
—
7...4.3 dial number plan (slt) on the off-hook condition
《dial plan 1》
dial operation
features
program
9 (0)
seize the idle co line
06 20
1-4
seize the idle co line of each queuing group
01
5 + queuing group
number
+ abbreviated dial number
abbreviated dialing by specific queuing groups.
※ queuing group number = 0: any queuing groups
1-6: group 1-6
※ abbreviated dial number = 00-99
000-999 (tx-1232/2464)
01
60+queuing group
number
last number redial by specific queuing groups.
※ queuing group number = 0: any queuing groups
1-6: group 1-6
01
61
answer to exclusive hold.
—
62
set dnd.
13
63 + extension number
+ option number
set ring transfer
※ extension number = 10-79 or 100-799
option = 0: ring transfer immediate
1: ring transfer when busy
2: ring transfer when unanswered
3: ring transfer when busy / unanswered
28
64 + hhmm
set wake-up call
※ hhmm: hour and minutes (0000-2359)
—
65 + personal code
set dial block
※ personal code = 4 digits (0000-9999)
35
66 + personal code
reset dial block
※ personal code = 4 digits (0000-9999)
35
69
all reset for mw, callback, ring transfer, wake-up call
and dnd.
—
7
seize intercom
—
8
call pickup to meet-me answer, intercom call, hold
transfer and disa call (same paging group).
—
0 (9) + trunk number
seize the specify trunk (outgoing call or answer to hold).
※ trunk number = 01-system max
16 20
06 (96)
call pickup to co line call.
07 20
07 (97) + security code
walking class of service
42
08 (98) +extension number
call pickup to intercom call, intercom hold, hold
transfer and disa call (specific extension).
※ extension number = 10-79 or 100-799
20
08 (98) + 80-87
meet-me answer
08 20
08 (98) + 88
meet-me answer (same paging group)
08 20
08 (98) + 9
call pickup to doorphone call.
20
09 (99) +extension number
seize last held co line on a specific extension.
※ extension number = 10-79 or 100-799
—
#
call pickup to intercom call, hold transfer and disa
call
(extension in same paging group)
—
《dial plan 2》
dial operation
features
program
9 (0)
seize the idle co line
06 20
extension number
intercom calling
※ extension number = 10-79 or 100-799
—
80
all call (all extensions on specified paging group)
※ external speaker calls at the same time possible
08
19
81-84
internal paging (each paging group)
08
85
external paging (external speaker 1 and 2)
—
86 / 87
call to the external speaker 1 or 2.
—
88 / 89
call to the doorphone 1 or 2.
—
0 (9) + trunk number
seize the specific trunk (outgoing call/answer to hold
line)
※ trunk number = 01-system max
16
20
03 (93) + queuing group
number + abbreviated dial
number
abbreviated dialing by specific queuing groups.
※ queuing group number = 0: any queuing groups
1-6: group 1-6
※ abbreviated dial number = 00-99
000-999 (tx-1232/2464)
01
051 (951)
answer to exclusive hold.
—
052 (952)
set dnd.
13
053 (953) +extension
number + option number
set ring transfer
※ extension number = 10-79 or 100-799
option = 0: ring transfer immediate
1: ring transfer when busy
2: ring transfer when unanswered
3: ring transfer when busy / unanswered
28
054 (954) + hhmm
set wake-up call
※ hhmm: hour and minutes (0000-2359)
—
055 (955) + personal code
set dial block
※ personal code = 4 digits (0000-9999)
35
056 (956) + personal code
reset dial block
※ personal code = 4 digits (0000-9999)
35
059 (959)
all reset for mw, callback, ring transfer, wake-up call
and dnd.
—
06 (96)
call pickup to co line call.
07 20
07 (97) + security code
walking class of service
42
08 (98) +extension number
call pickup to intercom call, intercom hold, hold
transfer and disa call (specific extension).
※ extension number = 10-79 or 100-799
20
08 (98) + 80-87
meet-me answer
08 20
08 (98) + 88
meet-me answer (same paging group)
08 20
08 (98) + 9
call pickup to doorphone call.
20
09 (99) +extension number
seize last held co line on a specific extension.
※ extension number = 10-79 or 100-799
—
*
call back to mw.
—
#
call pickup to intercom call, hold transfer and disa
call
(extension in same paging group)
—
4.4 dial number plan (kts) on the spk-on condition
dial operation
features
program
dial 0
seize the idle co line in the any queuing group.
01 15
dial 1-6
seize the idle co line each queuing group (1-6).
01 15
4.5 dial number plan (kts and slt：dial plan 1) on the intercom dt tone condition
dial operation
features
program
0
call to attendant
※ attendant = no. 10 extension, specific extension at
each tenant
51
extension number
intercom calling
※ extension number = 10-79 or 100-799
—
80
all call (all extensions on specified paging group)
※ external speaker calls at the same time possible
08
19
81-84
internal paging (each paging group)
08
85
external paging (external speaker 1 and 2)
—
86 / 87
call to the external speaker 1 or 2.
—
88 / 89
call to the doorphone 1 or 2.
—
9 + trunk number
seize the specific trunk (incoming call) note
※ trunk number = 01-system max
16
20
96
co line incoming call answer note
07
99 +extension number
seize last held co line on a specific extension. note
※ extension number = 10-79 or 100-799
—
*
call back to mw.
—
# + hunting group number
call to hunting group
11
note：refer to dial plan 1 for slt.
4.6 dial number plan (kts / slt) on the intercom call condition
dial operation
features
program
0
set mw (cut off intercom call).
—
1
change the voice / signal call.
19
*
set camo-on message
※ restrict to off-hook signalling call
04
#
step call
—
4.7 dial number plan (kts / slt) on the busy (intercom call) condition
dial operation
features
program
0
set mw (cut off intercom call).
—
1
set off-hook signalling
04
*
set intercom camo-on
※ hang up after dial "*", intercom callback set.
—
#
step call
—
4.8 dial number plan (kts / slt) on the intercom and external paging condition
dial operation
features
program
#
set meet-me answer
—
4.9 during seize the idle co line ? dial number plan ( slt ) after flashing
dial operation
features
program
extension number
intercom calling
※ extension number = 10-79 or 100-799
—
80
all call (all extensions on specified paging group)
※ external speaker calls at the same time possible
08
19
81-84
internal paging (each paging group)
08
85
external paging (external speaker 1 and 2)
—
86 / 87
call to the external speaker 1 or 2.
—
88 / 89
call to the doorphone 1 or 2.
—
90
flashing
26
91
set hold.
—
92
set exclusive hold.
—
93 + extension number
(flash from during
conversation)
set conference for 1 co line with 2 extensions
※ invite internal party.
—
94 + trunk number +
telephone number (flash
from during conversation)
set conference for 2 co line with 1 extension
※ invite internal party.
16
99 + account code
input account code
※ account code be able to set until 8 digits.
—
*
call back to mw.
—
# + hunting group number
call to hunting group
※ hunting group number = 0-4
11
4.10 dial number plan (kts / slt) from seize co line condition
dial operation
features
program
0, 1-9, *, #
send dial
※ dial "*" (for kts) can be used as starting and
finishing
command for account code entry.
01
4.11 dial number plan ( slt ) from busy ( seize co line ) condition
dial operation
features
program
queuing group number
queuing the co line
※ queuing group number = 0: any queuing groups
1-6: group 1-6
01
8...nitsuko tx-2464(nec ak 2464) end.
9...要是能打包就好了!
10...我是拆包帖上来的，打包的东西如何放上来？
11...有td88的全套资料吗，谢谢了，luh＠cncbb.net
12...班主,有没有阿尔卡特a4400的编程资料
向你买也行呀!
我好需要!
amoye＠vip.163.com
13...
.........请看原文: http://www.1000bbs.com/dispbbs.asp?boardid=64&id=42758&page=99&star=1 ◆◆◆相关技术贴子◆◆◆
|